Exactly How to Install a Bath Tub Yourself
Exactly How to Install a Bath Tub Yourself
Blog Article
What're your thoughts about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Installing a bathtub isn't precisely brain surgery, yet it does call for solid plumbing, carpentry, as well as occasionally, tiling abilities. Replacing an old bathtub with a new one is likewise a reasonably tough task. If the old bathtub is readily available, the job can relocate immediately; if you need to open up a wall to remove the old tub and position the new tub, the task is a lot harder. In either instance, the task is within a residence handyman's skills, although you will require a helper to vacate the old tub and set in the new one. Ensure you have qualified yourself for the task as well as are comfortable attempting it. Instead of employing a specialist to take over a halfway-completed job, it is much better to think about employing one prior to you begin. Chances are you might require an expert plumber to make tube connections.
This article will certainly aid you set up a new bathtub in your bathroom if you have actually already bought a brand-new tub and do not require to alter the arrangement of your previous water supply pipelines.
Your devices as well as material list must comprise the following:
Getting ready for the Installation
To start with, the supporting frame provided with the bath should be fitted (if called for) according to the maker's instructions. Next off, fit the taps or mixer to the bathtub. When suitable the tap block, it is important to make certain that if the tap features a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets system to prevent stress on the bathtub.
Fit the adaptable tap adapters to the bottom of both taps utilizing 2 nuts and olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Ensure you make use of all of the supplied washing machines.
Connect the trap to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath need to now prepare to be fitted in its last position.
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your installation, then the first thing you need to do is separate the water supply. After doing so, switch on the faucets to drain any type of water remaining in the system. The process of removing the existing faucets can be fairly bothersome due to the limited accessibility that is frequently the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipelines to the taps. Have a towel all set for the remaining water that will originate from the pipelines. Once the supply pipes have been gotten rid of, make use of the same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single taps from transforming throughout this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any old sealing substance.
Prior to going on to fit the new taps, compare the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new taps to fit.
Setting up the Tub
Utilizing both wood boards under its feet, position the bath tub in the called for placement. The wood boards are helpful in evenly spreading the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto 4 small points.
The next goal is to ensure that the bathtub is leveled all round. This can be achieved by checking the spirit level and adjusting the feet on the bathtub until the spirit level reads degree.
To mount faucets, fit all-time low of the outermost adaptable faucet port to the proper supply pipe by making a compression join; then do the same for the other tap.
Activate the water and also examine all joints as well as brand-new pipework for leaks and tighten them if necessary. Fill the bath tub as well as additionally inspect the overflow outlet and the normal electrical outlet for leakages.
Lastly, take care of the bath paneling as described in the manufacturer's user's manual. Tiling and also sealing around the bathtub should wait till the bath tub has actually been utilized at least when as this will certainly settle it into its last placement.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will require a plastic port to avoid damage to the string. One end of the port fits on the plastic tail of the tap and also the various other end offers a connection to the current supply pipes.
If you need to fit a monobloc, then you will call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the installing hole in the bath/basin making sure that the washers are in area between the tap and also the sink. Secure the faucet in place with the manufacturer given backnut. When the faucet is safely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal faucet connectors. The previous kind ought to be attached to the tap finishes initially, tightening only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the location where the bath fulfills the tile, it is essential to seal the accompanies a silicone rubber caulking. This is important as the fitting can relocate enough to break an inflexible seal, causing the water to permeate the wall surface in between the bath as well as the tiling, bring about complications with dampness as well as feasible leaks to the ceiling listed below.
You can pick from a range of coloured sealers to blend in your fixtures and also fittings. They are offered in tubes and also cartridges, and are capable of securing voids approximately a width of 3mm (1/8 inch). If you have a larger space to load, you can load it with twists of soaked newspaper or soft rope. Keep in mind to constantly load the bathtub with water before securing, to permit the activity experienced when the bathtub is in use. The sealant can split rather very early if you do not take into account this movement before sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise conveniently available on the market. It is recommended to fit the ceramic tiles making use of water-resistant or waterproof adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm just very occupied with A Step-by-Step Guide to Installing a Bathtub and I hope you enjoyed the blog posting. In case you appreciated our blog posting kindly make sure you remember to pass it around. Thank you so much for going through it.
Contact Us Today
Report this page